How To Repair Burnt Wood

Download Article

Download Article

Pieces of wood around your domicile, shop, or garage tin be inadvertently burned through regular wearable and tear, whether it'southward furniture, paneling, a tabletop, or a wooden toy. While in that location's no way to repair a piece of wood that'due south completely turned to ash, you tin get pocket-sized burn marks off of wood relatively easily. If y'all're working with a section of hardwood—eastward.g., floor from ash, oak, or beech trees—your all-time bet will exist to sand or scrape out the burned forest before patching the spot with epoxy.

1. 1

   Purchase fine steel wool to remove the burned surface. The steel wool method works all-time with small, shallow burns such every bit from cigarette ash. Visit a local hardware store and purchase the finest steel wool they sell. Steel wool with a ranking of 0000 (the finest) is platonic. If you can't find steel wool in a hardware store, cheque in a local domicile-improvement store.^[1]

   • Unlike sandpaper, lower numbers of steel wool are finer, but "fine" steel wools are marked with different numbers of zeroes. For example, 000 steel wool is "extra fine," and 00 is "fine."

2. 2

   Dampen the slice of fine steel wool with mineral oil. Before setting the steel wool against the woods, cascade about ¹⁄₂ teaspoon (2.5 mL) of mineral oil over the wool. This will lubricate the tendrils of the steel wool and prevent them from scratching the wood.^[two]

   • Purchase mineral oil at any hardware store or dwelling house-improvement store. If you don't have mineral oil on paw, you could use some other non-drying oil like lemon oil.

   Advertisement

3. three

   Scrub the dampened steel wool back and along beyond the burn down marks. Hold the steel wool in 1 mitt, and rub information technology in a single direction on peak of the fire mark in your hardwood. Rub along the grain of the wood, not beyond it (or you'll risk damaging the wood further). Afterward 10-12 passes, you'll observe that the burn marker has lightened substantially.^[3]

   • Keep rubbing with the steel wool until the burn is gone.

4. 4

   Absorb the oily area dry with a clammy make clean material. Once the burn marker has been erased, selection up a make clean scrap of cotton cloth and run a picayune tap water over it. You lot want the cloth to be lightly damp, so wring out as much water every bit yous tin. Don't rub back and forth across the wood, only lightly press the textile downwards onto the oily surface to soak upwardly the oil left behind by the steel wool.^[four]

   • If the cloth is also wet, you'll end upwardly leaving a water stain on the forest.
   • You lot shouldn't need to employ any kind of furniture polish when you're just dealing with a small-scale burn down mark. In nearly all cases, the oil will be enough to seal the expanse.

   Advertizing

1. ane

   Scrape off deeper burn marks using the blade of a utility knife. The only way to remove burn marks deeper than about ¹⁄_eight  in (0.32 cm) is to scrape out the burned woods itself. Take a utility knife and drag the edge of the blade over the burn to remove the damaged wood. Work in brusk strokes and make certain yous're post-obit along the forest grain, non cutting across it.^[5]

   • Buy a utility knife (and spare blades if you lot similar) at a hardware shop. Some stationery or role-supply stores may also sell them.

2. two

   Smooth out the damaged area with fine-grained sandpaper. If the wood surrounding the burn wasn't damaged when yous scraped out the burn, y'all should be able to even out the surface of the wood with sandpaper. Sand forth the woods grain (non across information technology) using back and along motions until the groove (where the burn used to be) has been smoothed out.^[6]

   • Local hardware stores volition sell sandpaper. Choose fine sandpaper with a number effectually 360 or 400. (When working with sandpaper, higher numbers signal finer grain.)

3. 3

   Brush off the leftover woods shavings with a damp rag. When y'all've finished scraping away the burn marker and sanding the surface of the woods, you'll exist left with a minor pile of woods shavings. To remove them from the woods, dampen a rag and rub information technology along the surface of the wood to remove the shavings.^[7]

   • It'southward of import that the rag you use is lightly damp. Otherwise, y'all'll just end up pushing the shavings around.

4. 4

   Utilise a layer of tung oil to the wood to restore its color. You tin can purchase tung oil at a pigment-supply store or a home-improvement shop. Dip a slice of clean textile into the tung oil and rub it over the formerly burned section of wood. Piece of work in strokes about iii–five inches (seven.6–12.7 cm) long, and exist sure to utilize the oil forth the forest grain, non across it. ^[8]

   • Depending on the colour of the wood you lot're repairing, you tin can besides endeavor using a linseed oil. The two oils are similar, and the simply major difference is that linseed oil yellows over time.
   • This will work to your advantage, though, if the wood yous're repairing has yellow tones.

5. 5

   Let the oil soak into the wood overnight. Since tung oil (and linseed oil) is nondrying, information technology will take several hours to absorb into the hardwood and harden in place fully. So, follow the directions provided on the tung oil's packaging regarding, as some tung-oil manufacturers may ask y'all to wipe off the oil rather than letting it soak into the wood.^[9]

   • If you're dealing with hardwood flooring and have kids or pets in your home, keep them away from the oily flooring until it's dry.

6. half dozen

   Fill the divot with wood epoxy until it's flush with the residual of the floor. Wood epoxy contains a number of chemical components that should be mixed together following the manufacturer'south instructions. Once the epoxy has reached a putty-similar consistency, apply a spackle knife to printing the epoxy into the hardwood hole where the burn down mark used to be.^[10]

   • Let the epoxy dry overnight, or for 6-8 hours. During this fourth dimension, be sure to continue any wandering children or curious animals away from the epoxy.
   • You should have no trouble finding an assortment of wood epoxies at a local hardware store or domicile-improvement shop.

7. 7

   Sand the epoxy flush with the floor using coarse sandpaper. A sheet of 80-grit sandpaper would work well for this step. Rub the sandpaper dorsum and forth several times across the dried epoxy until you've smoothed it downwards to the same level every bit the surrounding floor. Exist careful to avert sanding too much on the hardwood flooring itself. Yous don't desire to scuff upwards the undamaged forest accidentally.^[eleven]

   • In one case y'all're finished with the lxxx grit, if you like, effort sanding once more with 120-dust sandpaper to ensure that the epoxy is shine.

8. 8

   Stain or pigment the filled burn marker to match the colour of your flooring. Use stain or paint based on whether the surrounding floor has been painted or stained (in most cases, hardwood will need to exist stained). Dip a iii in (7.vi cm) paintbrush into the stain (or pigment), and apply a shine coat across the area y'all've repaired. Requite the stain (or pigment) at least 4-5 hours to dry, and employ a second layer if the new layer is darker than the rest of the flooring.^[12]

   • If you're unsure of the exact color of your flooring, you can test out sample paint or stain colors before using them. Test the textile on a pocket-size, out-of-the-way corner of the floor.

   Advertizement

1. one

   Mix together a thick paste of blistering soda and h2o. If you're dealing with a burn on a nighttime wood surface, the burn itself is well-nigh probable white in color. To remove the burn mark, combine well-nigh one tsp (0.3 g) of baking soda and ¹⁄₈ teaspoon (0.62 mL) of water in a small bowl. Use one finger (or a spoon if you prefer) to mix the two ingredients together until they grade a thick paste.^[13]

   • Keep the consistency of the paste dry. If you add too much water to the mixture, you'll end up giving the forest surface a water stain!

2. 2

   Vitrify the paste into the burn with a make clean cloth. Scoop up a small-scale dab of the thick baking soda paste with the corner of a scrap of clean cotton cloth. Rub the paste into the light-colored wood fire to gradually darken the color of the burn and eventually remove the fire mark birthday.^[14]

   • If a single dab of paste isn't enough to remove the burn marker, employ 2 or even 3 more than dabs of the paste.

3. three

   Apply a furniture polish to the restored surface of the forest. Spray a commercial forest shine onto a second scrap of make clean fabric. Then, rub the polish into the surface of the wood. This volition remove the gritty baking-soda paste and aid the restored patch match the rest of the forest. Wipe forth the grain of the forest, and employ the polish in smooth strokes, each about eight–10 inches (twenty–25 cm) long.^[fifteen]

   • If yous don't already have a furniture polish on hand, buy some at a local hardware store.

   Ad

Inquire a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Advertisement

Things You'll Need

• Stain-removal pad
• Mineral oil
• Steel wool
• Clean cloth
• Water

• Utility pocketknife
• Fine sandpaper
• Damp rag
• Clean material
• Tung oil
• Wood epoxy
• Spackle pocketknife
• 80-grit sandpaper
• 120-dust sandpaper
• Paint or stain
• 3 in (7.6 cm) paintbrush

• Baking soda
• H2o
• Basin
• Cotton material
• Spoon
• Article of furniture polish

• Steel wools with ratings of, for example, 3 and iv are considered "coarse" and "actress coarse," respectively.^[16]

Cheers for submitting a tip for review!

Advertisement

Most This Article

Article Summary X

To remove shallow burn marks from wood, all you'll demand is steel wool, mineral oil, and a cloth. Just dampen the wood with the mineral oil so the steel wool doesn't scratch it, so vitrify out the fire mark with the steel wool. To remove deeper burn down marks from wood, scrape away the burned material with a utility knife and sand information technology down. And so, fill in the gaps with forest epoxy and utilise a stain or paint on top to blend the repaired wood in with the rest of the finish. For more tips, including how to remove burns from dark wood, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 153,451 times.

Did this article aid y'all?

Source: https://www.wikihow.com/Remove-Burn-Marks-on-Wood

Posted by: grahamsheining.blogspot.com

Share this post